Uncategorized

How To Install A Deadbolt All By Yourself!

Installing a deadbolt is something you can do yourself, and save yourself a whole lot of money. Handiwork is very easy, and with a little bit of knowledge, a small set of common tools, and a wee-bit of time, you will have the job done like a piece of cake. Yes, like a boss! Whether it is Schlage, Kwikset, Yale, August, Samsung or name it! This guide will work for you.

Installing a Deadbolt: Fairly Easy

install-a-deadbolt

Tools required

  • Drill
  • Hole saw drill bit
  • Spade drill bit
  • Twist drill bit
  • Chisel
  • Screwdriver (most locks use Phillips-head)
  • Tape
  • Pencil
  • Utility knife
  • Hammer
  • Patience 🙂
Step 1: Getting Ready

The first thing you want to do to install a door lock is to take a look at your door.
Is there a pre-existing hole? If not, no problem. Most deadbolt door locks come with a template that shows you where to drill and screw. Start by figuring out where you want the lock to go. Keep in mind, some digital door locks have handles that are a little bit below the lock itself; if so, figure out where you want the handle, and line the lock hole up accordingly. When attaching the template to the door, use a combo square if you can, to ensure proper alignment. Also use tape that won’t tear paint off a door.

Step 2: Drill That Hole!

After you have chosen the location and taped the template to the door, it is time to start drilling the hole for the locking mechanism. Now, use a hole saw that matches the size of the hole on the template. Start drilling slowly, applying even and firm pressure to prevent it from moving. After you have drilled through to the other side, it is time to drill the hole for the bolt. Using a spade bit, drill the hole for the bolt where the template shows. It should line up with the hole you drilled for the mechanism. Check your template, as some locks require a bolt hole to be extended on the far side of the mechanism hole. One important tip when drilling: always stop when the pilot bit comes out the other side of the door, then pull the drill out and finish drilling from the other side; this will prevent the drill from cracking the wood. After drilling the holes, look on the template for the screw-holes, and drill pilot holes in each spot with a twist a little bit that is smaller than the screws themselves.

Step 3: Setting Up The Latch Plate

Now that the holes are drilled on the door, it is time to install the latch plate. Line the bolt hole up with the latch plate, trace the edge onto the door with a pencil or utility knife. Chisel out this area so that the latch plate sits flush on the door. Start by using light taps of the hammer onto the chisel handle, to ensure you don’t go too deep. Now attach the latch plate onto the door by screwing it into the holes you already should have drilled pilots for. Note, you will have to insert the bolt before you screw in the latch plate.

Step 4: Fitting The Strike Plate

The next step is to install the strike plate. The strike plate usually has 3 pieces, a strike frame reinforcement, a box for the bolt, and the strike plate itself. Lining up the bolt correctly with the hole you need to drill for the strike plate is very important. After you have done this, mark with a pencil where the screws will go for the reinforcement plate. Next, you want to mark where the screws will go for the strike plate; the screws for the strike plate usually also screw into the bolt box.
Now, using a spade drill (large enough for the bolt box), drill a hole deep enough to ensure it goes in, with about a 1/4 inch extra. The next step is to trace the outline of the reinforcement or strike plate, and chisel a hole onto the frame to insert the 3 pieces, ensuring that they fit flush. After this, screw in the reinforcer plate, then screw in the bolt box and then the strike plate.

Step 5: Putting The Lock In Place

Now it is time to attach the lock mechanism itself. This part is rather simple. Many electronic deadbolts have wires that connect the front of the lock to the back. Feed the wires from the front through the hole, and connect. Attach the axle that activates the bolt. Now, holding the front piece up, attach the rear piece, and screw them both together, making sure the screws are in tight. This should be it.

One final thing to do is to check the door over. Make sure the bolt on the door lines up with the frame. Make sure the lock works before while the door is open; the last thing you want is to lock the door while it is shut, and then find out it doesn’t unlock. When everything is good and works properly, it is time to start enjoying your new door lock.

KINDLY WATCH THE VIDEO TUTORIAL BELOW FOR LIVE STEPS:

You’re welcome 🙂
Don’t forget to share this page with friends.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Enjoy massive Amazon discount on the Best Overall Deadbolt right now. Only a few days left!Claim Discount